Mint NextMove PCI Installation Manual Page 53
- Page / 92
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation 5-11MN1903
4. If you are going to use the relay, drag the grey Relay0 icon to the grey X axis icon on the right
of the screen. To configure multiple axes to use the relay, repeat this step for the other axes.
If you are using a digital output, drag the bright blue OUT icon to the grey X axis icon on the
right of the screen. To configure multiple axes with the same drive enable output, repeat this
step for the other axes.
5. Click Apply at the bottom of the screen. This
sends the output configuration to the
NextMove PCI.
5.3.5 Testing the drive enable output
1. On the main WorkBench v5 toolbar, click the
Drive enable button. Click the button again.
Each time you click the button, the drive
enable output is toggled.
When the button is in the pressed (down)
position the drive should be enabled. When
the button is in the raised (up) position the
drive should be disabled.
If this is not working, or the action of the button is reversed, check the electrical
connections between the breakout module and the drive.
If you are using the relay output, check that you are using the correct normally open or
normally closed connection.
If you are using a digital output, check that it is using the correct high, low, edge or rise/fall
triggering method expected by the drive.
- NextMove PCI 1
- Motion Controller 1
- Contents 3
- Appendices 5
- General Information 7
- Safety Notice 8
- Precautions 8
- 2.1 NextMove PCI featu res 9
- 2-2 Introduction MN1903 10
- 2.2 Receiving and inspection 11
- ________________________ 11
- 2.3 Units and abbreviations 12
- 3.1 Introduction 13
- 3.2 Location requirements 14
- 3.3 Installation 15
- 3-4 Basic Installation MN1903 16
- 4.1 Outline 17
- 4.2 100-pin edge connector 17
- 4-2 Input / Output MN1903 18
- Input / Output 4-3MN1903 19
- 4.3 Analog I/O 20
- 4.3.1 Analog inputs - X6 21
- 4-6 Input / Output MN1903 22
- Input / Output 4-7MN1903 23
- 4.4 Digital I/O 24
- Input / Output 4-9MN1903 25
- 4.4.1 Digital inputs - X1 26
- 4.4.2 Digital inputs - X2 27
- 4.4.3 Digital inputs - X3 28
- 4.4.4 Digital outputs - X4 29
- 4.4.5 Digital outputs - X5 30
- 4.5 Other I/O 31
- 4.5.2 Encoder input frequency 32
- 4.5.3 Power - X9 33
- 4-18 Input / Output MN1903 34
- Input / Output 4-19MN1903 35
- 4.6 CAN Connections 36
- 4.6.1 CAN1 (CANopen) - X17 37
- 4.6.2 CAN2 (Baldor CAN) - X18 38
- 4.7 Other I/O 39
- 4.8 Reset states 39
- 4-24 Input / Output MN1903 40
- Input / Output 4-25MN1903 41
- 4-26 Input / Output MN1903 42
- 5.1 Introduction 43
- 5-2 Operation MN1903 44
- 5.1.4 Installing WorkBench v5 45
- 5.1.5 Starting WorkBench v5 46
- Operation 5-5MN1903 47
- 5-6 Operation MN1903 48
- 5.2 WorkBench v5 49
- 5.3 Configuring an axis 50
- 5.3.3 Selecting a scale 51
- 5-10 Operation MN1903 52
- Operation 5-11MN1903 53
- 5-12 Operation MN1903 54
- Operation 5-13MN1903 55
- 5-14 Operation MN1903 56
- Operation 5-15MN1903 57
- 5-16 Operation MN1903 58
- Operation 5-17MN1903 59
- 5.5.2 Underdamped response 60
- 5.5.3 Overdamped response 61
- 5-20 Operation MN1903 62
- Operation 5-21MN1903 63
- 5.7.1 Calculating KVELFF 64
- Operation 5-23MN1903 65
- 5-24 Operation MN1903 66
- 5.7.2 Adjusting KPROP 67
- 5-26 Operation MN1903 68
- 5.8 Step p er axis - testing 69
- 5-28 Operation MN1903 70
- Operation 5-29MN1903 71
- 5-30 Operation MN1903 72
- Operation 5-31MN1903 73
- 5-32 Operation MN1903 74
- 6.1 Introduction 75
- 6.2 NextMove PCI ind icators 76
- 6.2.2 Communication 77
- 6.2.3 Motor control 77
- 6-4 Troubleshooting MN1903 78
- 7.1 Introduction 79
- 7.1.5 Digital inputs (X3) 80
- 7.1.6 Digital outputs (X4) 81
- 7.1.7 Relay output (X8) 81
- 7.1.10CANopen interface (X17) 82
- A.1 Introduction 83
- A-2 Accessories MN1903 84
- Accessories A-3MN1903 85
- A-4 Accessories MN1903 86
- A.1.5 Digital output modules 87
- A.1.7 Spares 87
- A.1.8 Baldor CAN nodes 88
- Accessories A-7MN1903 89
- A-8 Accessories MN1903 90
Related products and manuals for Steppers Mint NextMove PCI
Steppers Mint NextMove PCI Installation Manual
(126 pages)
(126 pages)
© 2020, manymanuals.com. All rights reserved. | 1.878 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals